[Woodworkers] TS vibration

Jim Cabernoch jcabernoch at gmail.com
Sun Feb 20 17:40:20 PST 2022


Just my two cents--but definitely try the link belt.  Did that on my
jointer and it was like a new machine!!

On Sun, Feb 20, 2022 at 5:30 PM Steve Bigelow via Woodworkers <
woodworkers at lists.sawdusters.org> wrote:

> Your new belt may have some set to it. Have you considered a link belt?
>
> On Sun, Feb 20, 2022, 5:24 PM Ron Odum via Woodworkers <
> woodworkers at lists.sawdusters.org> wrote:
>
>> Thanks for the tip!  Ill try that tomorrow.. Got a lot of relearning to
>> do...
>>
>>
>> On Sun, Feb 20, 2022, 7:11 PM John McCaskill <jmccaskill at gmail.com>
>> wrote:
>>
>>> You changed the blade & belt, cleaned & oiled the bearings. May be you
>>> can align the blade with the miter slots? Here’s a link to a complete table
>>> saw tuneup, if the vibration isn’t tolerable. I tuned mine so it passed the
>>> nickel test (balance a nickel on edge on the table when the saw is running)
>>> quite a few years back, and it’s still not too bad.
>>>
>>> https://woodgears.ca/delta_saw/alignment.html
>>>
>>> John
>>>
>>>
>>>    - Everything is always okay in the end, if it's not, then it's not
>>>    the end.
>>>
>>>
>>> On Feb 20, 2022, at 7:02 PM, Ron Odum via Woodworkers <
>>> woodworkers at lists.sawdusters.org> wrote:
>>>
>>> 
>>> My Delta Contractors 10" saw used today for first time in 10+ years ago.
>>> Seems to have excessive vibration since last used.
>>> Installed new belt that may have made somewhat better...Cleaned&oiled
>>> bearings on motor & blade shaft...Changed blade but still seems to have
>>> excessive vibration than I remember.. Bearings seem OK...but not sure what
>>> else it could be ????
>>>
>>> _______________________________________________
>>> I want to be one of my friends for a day so I can see how cool it is to
>>> hang out with me.
>>> Woodworkers at lists.sawdusters.org
>>>
>>> To unsubscribe from this list -
>>> http://lists.sawdusters.org/listinfo.cgi/woodworkers-sawdusters.org
>>>
>>> Address to contact the list ADMIN staff -
>>> woodworkers-owner at lists.sawdusters.org
>>>
>>> _______________________________________________
>> I want to be one of my friends for a day so I can see how cool it is to
>> hang out with me.
>> Woodworkers at lists.sawdusters.org
>>
>> To unsubscribe from this list -
>> http://lists.sawdusters.org/listinfo.cgi/woodworkers-sawdusters.org
>>
>> Address to contact the list ADMIN staff -
>> woodworkers-owner at lists.sawdusters.org
>
> _______________________________________________
> I want to be one of my friends for a day so I can see how cool it is to
> hang out with me.
> Woodworkers at lists.sawdusters.org
>
> To unsubscribe from this list -
> http://lists.sawdusters.org/listinfo.cgi/woodworkers-sawdusters.org
>
> Address to contact the list ADMIN staff -
> woodworkers-owner at lists.sawdusters.org



-- 
 Jim Cabernoch
Owner
Cabbies Woodshop
Altadena, CA
626-296-1763
Cabbies Woodshop.com
Cabbies Woodshop on Facebook
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.sawdusters.org/pipermail/woodworkers-sawdusters.org/attachments/20220220/8370c26d/attachment.html>


More information about the Woodworkers mailing list