[Woodworkers] Miter Saw Capacity at 45

[Sid Hymes]

FWIW, I checked and my DW also bevels in both directions.

On Mon, Sep 9, 2019 at 7:11 PM Gary C Williams via Woodworkers <
woodworkers at lists.sawdusters.org> wrote:

> I have a 10" Festool sliding compound saw that I bought from a friend
> second hand and it is really great. I replaced a 10:" Bosch sliding
> compound saw with the Festool. The Festool can bevel in both directions,
> whereas the Bosch only beveled in one direction. Even though they are
> expensive, I  love my Festool.
>
> Gary Williams
>
>
>
> -----Original Message-----
> From: Sid Hymes via Woodworkers <woodworkers at lists.sawdusters.org>
> To: Chuck Steger <chuck.steger at gmail.com>; A Place Where Woodworkers Talk
> About Woodworking <woodworkers at sawdusters.org>
> Cc: Sid Hymes <rusara at gmail.com>
> Sent: Mon, Sep 9, 2019 7:00 pm
> Subject: Re: [Woodworkers] Miter Saw Capacity at 45
>
> Chuck,
>
> Yes, I have a 780 and it's one of the first sliding DeWalts. Specifically,
> it's a sliding compound crosscut 12" miter and it has a ton of board feet
> cuts on it. (Bad sentence, but you get my drift.) I previously had a 10"
> Makita "chop saw" (an "over the top model") which could only cut 3x6s w/o
> flipping the wood over to finish the cut. I would definitely recommend the
> sliding models: I frequently cut 2x10 and 2x12s on mine. (I've read good
> things about the newer Bosch models tho I've not used one personally.)
>
> I think you'll find the "depth capacity the same for any 12" saw; where
> the slider comes into play is allowing you to cut wider stock. The depth is
> limited by the distance from the table surface to the blade washer (or
> whatever blade guard is mounted) and allowing for the blade's depth below
> the table surface. Thus, a 12" blade will allow you to cut thru a 5" thick
> (+/-) board, assuming it has the power and the density of the wood, etc.
>
> Due to space constraints, I just shipped my ol' Craftsman RAS to a buddy
> and miss it already! (My RAS was about 30 years old and it was my second
> Craftsman and third RAS.)
>
> Hope this helps.
>
> Sid
>
> On Mon, Sep 9, 2019 at 12:01 PM Chuck Steger <chuck.steger at gmail.com>
> wrote:
>
> Sid,
>    Thanks. Yeah my PM66 will only crosscut 3” (seems like it should be
> more). I have my dad’s RAS (circa 1950 or 1960) and I use it for rough cuts
> (precise crosscuts on TS sled). I always said when the RAS dies, I’ll get a
> miter saw. Now 60-70 years later, darn thing is still running! I’ve been
> researching miter saws and the DeWalt DWS780 (12”) keeps popping up as top
> saw. Is yours the slider? I’m wondering if saws that come up over the top
> (vs sliders) have a greater depth capacity?
>
>    I’m thinking I may have to buy a miter saw.
>
> Chuck
>
> *From:* Sid Hymes [mailto:rusara at gmail.com]
> *Sent:* Sunday, September 08, 2019 10:59 PM
> *To:* A place where woodworkers talk about woodworking
> *Cc:* Woodworkers (Sawdusters); Chuck Steger
> *Subject:* Re: [Woodworkers] Miter Saw Capacity at 45
>
> A 12" miter saw (I have a DeWalt) will handle 3" stock at a 45*, as will
> my 12" table saw. My 10" Delta T/S won't, so find yourself a 12" setup and
> you should be good to go.
>
> On Sun, Sep 8, 2019 at 8:17 PM Chuck Steger via Woodworkers <
> woodworkers at lists.sawdusters.org> wrote:
>
> For those of you who own miter saws (I have a RAS), what is their 45
> degree cutting capacity? My lamp project has my stock at 3” and my TS will
> barely cross cut it so I know it won’t bevel it. The specs on miter saws
> that I see say 45 degree capacity is a 2 x 12. Does that mean only 2”
> thick? Could yours cut a 3” bevel?
>
> My options for my lamp project are (1) use the TS to get most of it, and
> then hand saw the rest, (2) use the band saw, (3) hand saw it, or (4) use a
> miter saw. I don’t like the accuracy of 1-3 so was wondering about a miter
> saw. I don’t own one but maybe this is my excuse J
>
> Chuck
>
> _______________________________________________
> I want to be one of my friends for a day so I can see how cool it is to
> hang out with me.
> Woodworkers at lists.sawdusters.org
>
> To unsubscribe from this list -
> http://lists.sawdusters.org/listinfo.cgi/woodworkers-sawdusters.org
>
> Address to contact the list ADMIN staff -
> woodworkers-owner at lists.sawdusters.org
>
> _______________________________________________
> I want to be one of my friends for a day so I can see how cool it is to
> hang out with me.
> Woodworkers at lists.sawdusters.org
>
> To unsubscribe from this list -
> http://lists.sawdusters.org/listinfo.cgi/woodworkers-sawdusters.org
>
> Address to contact the list ADMIN staff -
> woodworkers-owner at lists.sawdusters.org
> _______________________________________________
> I want to be one of my friends for a day so I can see how cool it is to
> hang out with me.
> Woodworkers at lists.sawdusters.org
>
> To unsubscribe from this list -
> http://lists.sawdusters.org/listinfo.cgi/woodworkers-sawdusters.org
>
> Address to contact the list ADMIN staff -
> woodworkers-owner at lists.sawdusters.org
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.sawdusters.org/pipermail/woodworkers-sawdusters.org/attachments/20190910/cf91323e/attachment-0001.html>