[Woodworkers] Resin Table

Steve Bigelow sbig333 at gmail.com
Wed Aug 4 14:11:50 PDT 2021


It's starting to come together nicely, Chuck.

I've got some cherry I've been wanting to do something similar with,
although I was thinking of a live edge cutting board or charcuterie board.
I've been putting it off because I didn't want to deal with flattening the
two pieces once glued together, but my 2x4' CNC is up and running so I can
just use that now. Still need to get my 4x8' CNC running, but all in good
time.

Regards,
-Steve
http://woodworking.bigelowsite.com



On Wed, Aug 4, 2021 at 1:06 PM Dominic58 <dominic58 at comcast.net> wrote:

> Very nice but I have to point out that in that second picture, if you
> would have cut out the lighter wood of the piece to the right you’d have
> yourself an Elephant profile!!
>
> Thank you
> Dominic P
>
> On Aug 4, 2021, at 3:07 PM, chuck.steger--- via Woodworkers <
> woodworkers at lists.sawdusters.org> wrote:
>
> 
>
> Steve,
>
>    I used Liquid Glass. It’s the first time I have used it. It’s on the
> lower end of the price line so I didn’t know if this was a “you get what
> you pay for” moment but so far I am really pleased.
>
>    I’m attaching a couple of pictures of the top and underside when it was
> sanded to 400 grit. I’m making the aprons now. I decided that I wanted a
> resin stripe down the middle of the apron so I am making the forms now.
> Cross your fingers 😊
>
>
>
> Chuck
>
>
>
> *From:* Steve Bigelow <sbig333 at gmail.com>
> *Sent:* Tuesday, August 03, 2021 4:33 PM
> *To:* woodworkers at sawdusters.org
> *Cc:* chuck.steger at gmail.com
> *Subject:* Re: [Woodworkers] Resin Table
>
>
>
> I'm still getting caught up on emails after being gone for two weeks, but
> it looks like this is coming along nicely!
>
>
>
> What resin did you end up using here? I've been thinking about making one
> of these.
>
>
> Regards,
> -Steve
> http://woodworking.bigelowsite.com
>
>
>
> On Mon, Jul 26, 2021 at 5:18 PM chuck.steger--- via Woodworkers <
> woodworkers at lists.sawdusters.org> wrote:
>
>    This is the top (both sides) straight off of the slab flattening jig. I
> need to sand both sides down but wanted to show it now that it’s cleaned up.
>
>    The slab flattening jig was well worth the effort to make. If you can,
> flatten outside because it makes a mess. I did it inside because my
> workbench is my flattest surface. There was a lot of vacuuming during and
> after. My 2” surfacing router bit was not an issue for a couple of reasons.
> It fit my 2 ½ hp router base opening plus I needed to use an extension
> router collar so it hung below the base anyway. It worked out because I
> kept the router in the slab flattening carrier. I need to make the legs and
> apron but so far so good.
>
>
>
> Chuck
>
>
>
> *From:* chuck.steger at gmail.com <chuck.steger at gmail.com>
> *Sent:* Thursday, July 22, 2021 8:45 AM
> *To:* woodworkers at sawdusters.org
> *Subject:* RE: [Woodworkers] Resin Table
>
>
>
>    I just realized that I may have confused some people, especially if
> you’ve never done a resin pour. Most people who do a river table will take
> a board with natural edges on both sides and then split that board straight
> down the middle. The straight parts become the edges of the table and the
> wavy natural edges become the river (in the middle). You can then make the
> river as wide as you want.
>
>    In other cases (like mine), I wanted the resin to also be the edges. If
> you look at the before picture you will see the edges are natural and wavy.
> My resin is a translucent blue and if you look at after the pour, you can
> see the outline of the board edges. They say to make the form a little
> bigger than you want (in this case) so you can trim to the size you want.
> Once I plane down to the wood, the edges should become even clearer. At
> this point I plan on keeping the edges straight but another option would be
> to follow the curves and do some sort of edge treatment. I’m playing all of
> this by ear.
>
>    I wanted to clarify since this isn’t a true river table.
>
>    I was prepping my router for the surfacing bits. My largest router
> (DeWalt 3 ½ hp plunge) will not accommodate a 3” bit. I think 2” may fit.
> The bit will have to hang below the router base. I have to be very careful
> because a plunge router’s natural tendency (because of the springs) is to
> return up. I’ll have to hang the bit off of the wood (in my slab carrier)
> in a “free space”, slightly above the wood but away from my router base.
> Then I’ll plunge to a depth (set by my depth stop) and do a pass. Without
> raising the bit and in my free space, I’ll adjust the micro depth adjuster
> up a scootch and then plunge again. I’ll do this until I need to stop and
> check in which case I’ll return to my free space and shut off the router
> without retracting. This makes me nervous but as long as I am aware, I
> should be ok.
>
>
>
> Chuck
>
>
>
> *From:* chuck.steger at gmail.com <chuck.steger at gmail.com>
> *Sent:* Tuesday, July 20, 2021 3:51 PM
> *To:* woodworkers at sawdusters.org
> *Subject:* RE: [Woodworkers] Resin Table
>
>
>
>    Some “before” pictures. Hopefully the “after” pictures will be better
> 🤞
>
>    As usual, I appreciate everyone’s tips! I spent yesterday making a
> shop-made slab flattening jig. I finished the router carrier and rails but
> then realized my only planer bit is a dado clean out bit. It’s too small
> and would take forever to do a slab. I ended up ordering 2 bits: (1) A
> Whiteside surfacing bit, ½” shank, with carbide tips, 2” cutting diameter
> and (2) a Binstak surfacing bit with Helix cutters, ½” shank, 3” cutting
> diameter. The helix cutters gives me 4 edges each and I ordered extra
> cutters. It will be interesting to see which one cuts smoother.
>
>    Early into the project, I already have lessons learned:
>
>    - I made the form pretty well. Very little leakage (very little) and
>    used packing tape on the bottom and insides. The sides popped off easily
>    and the bottom came off easily after using a wide putty knife.
>    - The mix went well. I used powdered pigment instead of liquid. Some
>    people think liquid changes the chemistry of the mix. Thoughts on that?
>    I’ve used liquid in small applications like filling a knot but also realize
>    that big-box epoxy is way different than deep pour epoxy.
>    - For first timers like me: The deep pour epoxy is real thin so you
>    have plenty of time to work with it (keep this in mind when making the
>    form). Mine said a 72 hour cure. The longer the cure, the more time air
>    bubble can come to the surface. I used a heat gun to bring bubbles to the
>    surface and even after that, some still rose (not a problem as I will need
>    to surface anyway). Thoughts on heat gun vs torch?
>    - I did not flatten the wood before the pour. My thought process was
>    it was only 4/4 thick and if I flatten now and then again after the pour,
>    it would be too thin. Not sure if that is a valid way to think about it.
>    After watching more YouTube videos I think I could have saved epoxy and not
>    have near the cleanup if I had flattened first.
>    - I should have screwed the wood down from the bottom. I didn’t
>    realize it was floating until I noticed the cracks weren’t complexly
>    filling. Some YouTubers use hot melt glue. Thoughts on holding wood down?
>    One YouTuber used clamps but he had silicone pads to place the clamp head
>    on. In the photos, the brick did help but I think the buildup on the bottom
>    had already started. With 2 bricks touching wood, one came off clean and
>    one was solidly epoxied to the top. Red brick is real hard and it would
>    have taken a long time to sand off so I chiseled it off.
>    - Given the wood wasn’t flattened before and I didn’t screw down the
>    wood, I really overpoured. At the time I though that more was better and
>    that I could always clean it up. In hind sight I’m having to clean up more
>    and the underside of the top has 1/8” thick resin build. I think some would
>    have leaked on the bottom but not 1/8” thick. A lot of YouTubers will
>    either fill slightly under to plane wood first and some fill slightly over
>    but none fill like I did ☹
>    - I left the bark on. One YouTuber thought the bark could separate
>    from the wood. I think the epoxy was so thin, it permeated the bark and
>    will hold. Thoughts?
>    - I’m glad I started with a small table.
>
>
>
> Chuck
>
>
>
> *From:* Woodworkers <woodworkers-bounces at lists.sawdusters.org> *On Behalf
> Of *Gary C Williams via Woodworkers
> *Sent:* Monday, July 19, 2021 1:01 PM
> *To:* woodworkers at sawdusters.org
> *Cc:* gcw804 at aol.com
> *Subject:* Re: [Woodworkers] Resin Table
>
>
>
> Chuck,
>
>
>
> Show us some pictures when you get a chance.
>
>
>
> No matter what you use, you are either going to load up the sanding disks
> and belts, or dull your planer blades and router bits. I would probably go
> the route of using a jig and a router to level it, and then come back and
> do the final sanding with a Micro Mesh sanding pads..
>
> Router bits are relatively inexpensive.
>
>
>
> Make sure to wear a respirator.
>
>
>
> Good Luck.
>
>
>
>
>
> Gary Williams
>
>
>
>
>
>
>
>   Which leads me to my questions:
>
>    What do you use to level the table and sand the resin? I tried a belt
> sander but it loads up real quickly. Will the resin dull my planer knives
> if I send it through the planer? I have a drum sander but if the belt
> sander loaded up, wouldn’t the drum sander? I thought about putting it back
> in the form and use a router to level. The top wasn’t totally level but I
> could use wedges to level, then route. The underside of the top has a good
> 1/8” to 3/16” of resin and I’d like to take that down to the wood. One
> YouTube video said they liked Micro Mesh sanding pads because they are
> porous and vacuum easily but that would be a lot of sanding to remove 1/8”
> or more.
>
>    Advice? Thanks!
>
>
>
> Chuck
>
>
>
> _______________________________________________
> I want to be one of my friends for a day so I can see how cool it is to
> hang out with me.
> Woodworkers at lists.sawdusters.org
>
> To unsubscribe from this list -
> http://lists.sawdusters.org/listinfo.cgi/woodworkers-sawdusters.org
>
> Address to contact the list ADMIN staff -
> woodworkers-owner at lists.sawdusters.org
>
> _______________________________________________
> I want to be one of my friends for a day so I can see how cool it is to
> hang out with me.
> Woodworkers at lists.sawdusters.org
>
> To unsubscribe from this list -
> http://lists.sawdusters.org/listinfo.cgi/woodworkers-sawdusters.org
>
> Address to contact the list ADMIN staff -
> woodworkers-owner at lists.sawdusters.org
>
> <IMG_6465.JPEG>
> <IMG_6466.JPEG>
> _______________________________________________
> I want to be one of my friends for a day so I can see how cool it is to
> hang out with me.
> Woodworkers at lists.sawdusters.org
>
> To unsubscribe from this list -
> http://lists.sawdusters.org/listinfo.cgi/woodworkers-sawdusters.org
>
> Address to contact the list ADMIN staff -
> woodworkers-owner at lists.sawdusters.org
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.sawdusters.org/pipermail/woodworkers-sawdusters.org/attachments/20210804/fc47a70f/attachment-0001.html>


More information about the Woodworkers mailing list